The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.     

Experimental investigation of the normal spectral emissivity and other thermophysical properties of pulse-heated Ni-Ti and Au-Ni alloys into the liquid phase

1. Introduction Metal working industry needs accurate thermo- physical properties of liquid metals and alloys as input data for different simulation routines to im- prove the performance of their products. Within this paper we continue the systematic investigation of the dependence of emissivity of binary alloys on the relative concentration of the constituent elements (for a previous paper see [1]). 2. Experimental method A fast ohmic pulse heating technique is applied to heat metallic wire-s…     

亚硝酸钠作释放剂选择性螯合滴定法测定钯

用EDTA螯合Pd^2 和其它金属离子，然后用亚硝酸钠分解Pd—EDTA螯合物，释放出的ED—TA用Zn^2 标准溶液进行返滴定。大量各种金属离子都不干扰。用于测定Pd—Cu合金镀层、Pd—Sn—Cu合金镀层和Pd—Ti—Si合金中的钯，获得相当满意的结果。     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

The hydrogenation of triglycerides using supported alloy catalysts. I. Silica-supported Ni—Ag catalysts

Silica-supported Ni-Ag catalysts with a loading of 2·1·0.6% (w/w) total metal have been prepared using the precursors nickel dimethylglyoxime and silver nitrate by means of a simple impregnation method. The resulting catalysts were activated by calcination at 260°C in air, followed by hydrogen reduction at 450°C. They were then employed for soyabean oil hydrogenation at 1 bar H2 pressure and 160°C in a stirred batch reactor. Characterisation of the catalysts using temperature-programmed reduction and electron microscopy indicated that alloying of nickel and silver had occurred, but metal particle composition, for a given overall composition, varied with metal particle size and smaller metal particles were nickel rich. The hydrogenation activity and selectivity measurements revealed that the catalysts were more active and selective than a commercial nickel catalyst. Furthermore, the specific activities of the alloy catalysts were a maximum for alloys in the range 70–90 at. % Ni. However, the supported alloy catalysts also gave rise to greater trans isomerisation than the commercial catalyst. This is attributed to hydrogen deficiency caused by large triglyceride molecules blocking hydrogen chemisorption on small nickel particles (10–50 Å in diameter), leading to enhanced cis-trans isomerisation.     

住宅建筑带钢副框铝合金门窗防渗漏施工技术

使用自粘性防水卷材对带钢副框的铝合金门窗窗边进行粘接,以防止雨水通过副框与墙体之间的缝隙渗漏到室内,重点介绍了详细的施工措施。     

Solving regularized least squares with qualitatively controlled adaptive cross‐approximated matrices

The adaptive cross‐approximation (ACA) technique is applied to accelerating an inverse‐problem solver that estimates charge distribution on a dielectric spacer. The ACA generates an approximated system‐matrix that enables us to carry out high‐speed inverse calculation. We designed an approximation procedure based on ACA with some additional concepts, that is, (a) partitioning of matrix based on algebraic information, (b) approximation quality control based on matrix norms, and so on. The tested solver (LSQR for regularized least squares) with ACA demonstrates about 10 times faster performance than that without ACA. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(3): 10–18, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20326     

铝合金穿孔板吸声墙面施工技术

以教育部综合办公楼工程的机房铝合金穿孔板吸声墙面施工为例,介绍其固定件及吸声墙面的做法。     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.